Pocket doors for bathroom remodels can free up floor space, but the choice is made on the wall, not the door. A pocket door slides into the wall. So the wall has to be able to hold it.

The way to decide is to ask your builder what’s inside the wall where the door would slide. Do it before the plan is final and before the frame is bought. Skip that step, and a pocket door picked from a photo can turn out to need a wall that holds pipes, wires or a switch. Or the wall may not be able to carry the tile you’d planned for it. Then the plan changes after the frame is already bought.

Can Your Bathroom Wall Hold a Pocket Door?

It can, but only if the wall has room inside it for the door and its frame. A pocket door doesn’t swing out. It slides into a hollow space in the wall. As a general rule, what’s already inside that wall decides whether the door can go there. So judge the wall first.

On one frame maker’s pocket door frame page, the kit holds the hardware for a single pocket door installation in a two-by-four stud wall. The same page says that frame can be adapted for other wall thicknesses and for masonry walls.

The same maker also sells a second series, and its second frame page says that kit is made for a two-by-six stud wall. So even one maker offers different frames for different walls.

So the first job is to learn what kind of wall your bathroom has and what runs through it. As a general rule, ask your builder to check the wall where the door would slide. Ask about pipes, wires, ducts and switches. Then ask what would have to move. A wall that holds a sink supply or shower plumbing deserves a close look, and it’s worth raising before the layout is set.

The light switch deserves its own question. A switch beside a bathroom door can sit in the very wall a pocket door would slide into. Picture a switch plate right where the door needs to go. Something has to move, so decide it on paper first. Ask your builder where the switch can go instead.

What Does a Pocket Door Frame Kit Leave Out?

On that maker’s pages, the kit covers the hardware for a single pocket door installation. The pages also say the door, jambs, drywall, door locks and door pulls are not included. So a frame kit isn’t a finished door. It’s the part that goes inside the wall, and the rest has to come from another source.

That means the plan needs each of those pieces from somewhere. As a general rule, ask who supplies the door and the finish trim. Ask who handles the drywall work. Ask, too, about a privacy lock and pull made to work on a sliding door. Settle those answers before the frame is ordered.

That maker also lists a plywood clip set for its frames. The listing says the set adds strength and rigidity to pocket door walls. It also says the set gives a solid mounting structure to hang objects or tile. The plywood isn’t included.

In a bathroom, that can matter. If the pocket wall will carry tile or hold a mirror, ask your builder how the wall will support it. The same goes for a towel bar. Get those answers before the walls close up.

Is a Pocket Door Right for a Small Bathroom?

It can be. A pocket door doesn’t swing into the room, so the space a swinging door would sweep through is free to use. That can help a tight bath feel easier to move around in. The catch is the wall beside the opening. It needs the room the door slides into.

Picture a narrow bath where the door swings in and you have to step around it to close it. A pocket door can take that swing out of the room. That’s the appeal.

So weigh what the door gives against what it asks. You get floor space back. In return, it can ask for clear wall beside the opening, a wall that can hold the door, and a lock and pull that suit a door that slides out of sight.

Privacy is part of the weigh-up. As a general rule, a bathroom door needs a way to lock, and a door that disappears into the wall can need a lock and pull made for that. Pick them with the door, not after. It’s also fair to ask your builder how much sound the closed door will let through.

A pocket-door swap is one of the small-bath moves Kitchen Design Partners routinely recommends when planning a small bathroom layout.

Whether that swap works in your bath still depends on the wall. So the same questions apply. Ask what’s inside the wall and whether there’s clear room beside the opening. Ask where the door will stop when it’s closed, too.

How to Plan Pocket Doors for Bathroom Remodels Before Anything Is Ordered

A handful of questions can settle the door before anything is bought. As a general rule, put these to your builder while the plan can still change:

  • Ask what’s inside the wall where the door would slide.
  • Ask where the opening, the door stop and the light switch will fall.
  • Ask how much clear wall the door needs to slide fully open.
  • Ask what the frame kit leaves out and who supplies each piece.
  • Ask how the wall will carry tile or anything you’ll hang on it.
  • Choose the privacy lock and pull along with the door.

These are questions to settle while the plan is still a drawing. Once the frame and the drywall are ordered, a change can mean moving what’s in the wall or redrawing the layout.

Kitchen Design Partners offers kitchen and bath design services that include consultation, design planning and coordination with your builder or installer. With bathroom design and remodeling, the wall question goes to your builder while the layout is worked out in the design.

Frequently Asked Questions About Bathroom Pocket Doors

Are pocket doors good for bathrooms?

They can be. A pocket door frees the floor space a swinging door would need. As a general rule, it suits a bathroom when the wall can hold the door and you’re comfortable with the trade-offs. Talk through the privacy lock and pull with your builder, plus how the door handles sound. Then judge it on the wall, not on looks alone.

Can any bathroom wall take a pocket door?

Not every wall can. What’s inside the wall and how it’s framed decide that. One frame maker’s kits are made for two stud-wall depths: a two-by-four wall and a two-by-six wall. That maker’s page also says the frame can be adapted for other wall thicknesses and masonry walls. Your builder is the one to check the wall where the door would slide.

What does a pocket door frame kit include?

On one frame maker’s pages, a kit holds the hardware for a single pocket door installation. Those pages say the door, jambs, drywall, door locks and door pulls are not included. So plan where each of those pieces will come from before the frame is ordered. It’s worth settling with your builder while the plan is still a drawing.

Can you hang things or tile a pocket door wall?

One frame maker lists a plywood clip set for its frames. The listing says it adds strength and rigidity to pocket door walls and gives a solid mounting structure to hang objects or tile. The plywood isn’t included. If your pocket wall will carry tile or a mirror, ask your builder how the wall will hold them before the walls close.

Will Kitchen Design Partners help me plan a bathroom pocket door?

Kitchen Design Partners specializes in kitchen and bath design, so a pocket door can be part of your bathroom design conversation. The first step is to schedule an appointment. The team will discuss your needs, tour the showroom with you and start developing a customized design plan. Your builder or contractor handles construction and installation.

Check the Wall Before You Choose the Door

Kitchen Design Partners specializes in kitchen and bath design, custom and semi-custom cabinetry, countertops and tile, and guides each choice in the right order.

As a general rule, a pocket door is easiest to judge once you know what’s behind it. Find that out before the frame is ordered, and the rest of the choice gets simpler.

You’re welcome to visit the showroom in Northbrook, where you can explore different kitchen layouts, styles and materials. When you’re ready, bring your bathroom photos or inspiration and schedule a design consultation to talk through pocket doors for bathroom remodels and what your wall can hold.